Installing a xiaomi router. XiaoMi Mi Nano WiFi Router - Review and Feedback

14.07.2023

The Xiaomi brand is primarily famous for its mobile devices. They have long won the hearts of customers thanks to their excellent combination of price and technical capabilities. However, Xiaomi's product line is much wider than it seems at first glance. In the company's assortment you can find various products, everyone will find what they need. Today we’ll look at the Xiaomi Mi Wi-Fi 3 router. This model has a low price and attractive characteristics, which can interest the residents of our country. Today we’ll tell you how to set up a Xiaomi Mi Wi-Fi 3 router. We’ll also get acquainted with its features.

The device is equipped with an MT7620 processor with a frequency of 580 MHz. The Xiaomi router has 128 MB of RAM and 128 MB of internal memory. There are two wireless radio units. The first is at 2.4 GHz and speeds up to 300 Mb/s, and the second is at 5 GHz with connectivity up to 867 Mb/s. The cables to the router are connected to the WAN port and two LAN inputs, the speed of each reaches 100 Mb/s. In addition, there is a USB 2.0 connector.

The strength of the model is that it belongs to a very affordable price range. At the same time, the device can be safely called balanced, which cannot but attract attention. Also a plus was the radio unit operating at a frequency of 5 GHz. Of course, speeds up to 867 Mb/s are not always needed. But it’s nice to have a device with such capabilities.

Xiaomi Mi Wi-Fi 3 router in action

The processor resource allows the router to work without problems. The device maintains stable communication, no drawdowns were noticed. If the optimal firmware is installed, then the performance will not cause any complaints. You also need to properly configure the Xiaomi Mi Wi-Fi 3 router, but more on that later. The tests showed that the router, when operating in IPoE and PPPoE modes, reached 90 Mb/s. This is if we talk about one-way transmission, but even in full-duplex modes the device behaves quite decently. Impressive performance was a result of the use of a good hardware accelerator embedded in the chip.

The Xiaomi router has difficulties using the L2TP and PPTP modes; the speed level is significantly reduced. It can be seen that they are poorly optimized, but this is not particularly upsetting, because these modes are not so common. For full operation, what the PPPoE and IPoE modes offer is enough. Using a VPN, data is downloaded from the World Wide Web and the local network from your provider. In this case, the speed does not decrease, it even increases in certain scenarios. As you can see, the parameters of the Xiaomi Mi Wi-Fi Router 3 router are quite good; we’ll talk about how to configure it further.

Setting up a Xiaomi Mi Wi-Fi 3 router

The main difficulty in connecting and setting up the Xiaomi Mi Wi-Fi 3 router is the inscriptions in Chinese. However, this cannot be called an obstacle to connecting the device for further use. For those who do not understand how to configure the Xiaomi Mi Wi-Fi 3 router in Russian, we can recommend various services, for example, Google Translate. After all, the setup is done online. Thus, entering the necessary settings will not be difficult, because everything is clear. In addition, you can immediately update the firmware to the latest version, if one is offered, this is an additional benefit of online configuration. However, not all users know how to connect a Xiaomi router to the Internet. To do this, you need to make a considerable effort to become familiar with the interface that the device is equipped with. It is important to follow the correct sequence of actions. Then you won’t need much time to set up the Xiaomi Mi Wi-Fi 3 router; step-by-step instructions can help you in this matter.

We go to the resource http://miwifi.com/, it will act as an interface. The setup of the Xiaomi Mi Wi-Fi router has begun. We enter the necessary data in the appropriate fields, which includes the passwords of the admin panel, as well as your Wi-Fi. After these steps, the automatic configuration of the router will start. It will reboot, after which it will display that the installation is complete.

But before you configure Xiaomi Router 3 completely, you need to connect again. The same passwords are used this time. We gain access to the control panel, now we see four tabs - memory, routing status, general and additional settings. First, we need the general settings section; all available fields are filled in here. This will allow the router to connect to the Internet.

It would also be a good idea to familiarize yourself with the remaining tabs. With their help, software is updated, VPN is turned on and off, backups are made, and much more. Here is the answer to the question: how to configure the Xiaomi 3 router. But if you have not encountered all this before, at first you should not touch tabs that are not related to general settings. It’s better to understand everything well; the connected options can lead to a significant reduction in speed limits.

What is alternative firmware?

It is recommended to use standard software, but many are interested in how to configure a Xiaomi router using alternative firmware. For example, you can use the developer version, which opens the built-in operating system to the user. Due to this, functionality is expanded, performance and stability are increased, as well as the level of speed. Alas, such firmware cannot be found in finished form. However, you can use available open source sources for your own purposes to create a prototype firmware that will be customized to your preferences. You need to work hard to get the treasured advantages, such as support for PPTP and L2TP modes, Russian and English interface languages, an increase in the number of connected USB devices, and so on.

However, it is better to contact a specialist, since independent actions can lead to a complete stop of the router. Also, unskilled intervention in the settings can lead to loss of remote control of services, and options related to mobile devices may also become unavailable.

Work together with Mi Wi-Fi+

Many have heard about such a device as Mi Wi-Fi+. It essentially duplicates the operation of the main device, that is, the router. Although there are different opinions about this gadget. Some consider it a repeater, while others consider it a Wi-Fi signal booster. If you use it in conjunction with a router, the coverage area will expand significantly. The price of Mi Wi-Fi+ is approximately $8, it is extremely convenient to use due to its compact size. To understand how to connect the Xiaomi Router 3 router with this gadget to the Internet, you don’t need any special knowledge, everything is quite simple. When two devices operate simultaneously, the signal will become more stable or appear where there was none at all. But you shouldn’t get too carried away with the operation of the router together with Mi Wi-Fi+, although this gives some positive results. This may negatively impact your overall connection speed.

Conclusion

This device from a well-known Chinese manufacturer rightfully takes its place among the best routers in the mid-price category. And it’s not at all difficult to figure out how to configure the Xiaomi Mi Wi-Fi router; the router turned out to be simple and effective in operation. And the tempting price tag, good technical components, along with reliability make it very interesting in the eyes of the buyer. Xiaomi manages to do well not only smartphones; other products are also worthy of attention.

http 192.168.31.1 and miwifi.com are the addresses used to enter the settings of the Xiaomi Mi WiFi 3 router, as well as its brothers, the cheaper 3C and the top-end 3G. For many who like to order equipment from China, IP 192.168.31.1 has become quite familiar. After all, it is under it that the entrance to the administrator panel of Mi WiFi routers, as well as other network equipment of this company, is hidden. Today we will talk about how to set up Xiaomi Mi Router 3, but the instructions are also relevant for other models - Xiaomi Router 3G, 3C and earlier or, which have already been discussed on our website.

With all the advantages of this manufacturer, it has one significant drawback, which is typical for devices that have only recently entered the market and are not adapted for foreign users - if you go into its settings, the entire interface will first be dotted with spider hieroglyphs in Chinese, so for a beginner, If you have just purchased this router, you may experience problems when connecting for the first time. We tried to show as clearly as possible step by step and in pictures the entire process of setting up the Xiaomi Mi WiFi Router 3, 3G and 3C router.

How to connect Xiaomi Mi WiFi 3 router to a computer?

I think it makes no sense to say that the first thing you need to do is connect the Xioami Router via a power adapter to the mains - it’s understandable.

After that, it will immediately start distributing password-free WiFi “Xiaomi” - you can connect either via cable or wirelessly. If you are not connecting via WiFi, connect an Internet cable from your provider to the blue WAN port, and an Ethernet cable to your computer to the LAN.

Also make sure that in the “Local Area Connection” or “Wireless Connection” settings in the “Network and Sharing Center” of Windows on the computer itself, automatic acquisition of an IP address and DNS is set - this is the only way to get into the admin panel at the same time IP address 192.168.31.1, and at the web address miwifi.com.

To be on the safe side, if you get your hands on the Xiaomi Router, you can do a complete reset of all previous settings - to do this, use a pin to press the Reset button on the switched on router, which is recessed into the case.

192.168.31.1 - enter the settings of the Xiaomi router - miwifi.com

The router will automatically detect your type of Internet connection and in the next step we will only need to enter the required parameters for access - for me it is PPPoE, where you need to enter your login and password.

If the type of connection to the Internet is from a DHCP provider (that is, when you don’t need to configure anything on your computer or router to access the Internet), then to select this type, click on the item of the same name in the lower menu.

On the next page, set a password to log into the admin area and click the confirm button.

We wait until the settings are applied and the router reboots - pay attention to the QR code, it contains an encrypted link to download the mobile application.

How to configure Xiaomi Mi 3 WiFi Router?

After this, the Internet will work on our computer and all devices that will be connected to the created WiFi network. Let's go back to the admin area. Everything here is in Chinese, but by using one of the translator extensions for the browser (it is already built into Google Chrome), all the text is miraculously Russified. To do this, in Chrome, right-click on the page and select “Translate to Russian”

Notice how cool the admin panel is. The main page displays summary current information about the network - which devices are connected, how much traffic they use, what is the memory and CPU load. I have not seen anything like this from any other competitor in the budget class.

The “Equipment” menu displays a list of connected devices - right there, without unnecessary hassles, you can use switches to cut off the Internet for each of them.

“General Settings” contains all the basic network functions. For example, you can create a separate guest network without access to internal local resources.

“Internet Settings” - in addition to configuring the connection to the provider, you can choose to limit the speed of the WAN port, clone the MAC address and switch to Wi-Fi repeater mode.

In “Advanced settings” there are more detailed things, such as port forwarding, manually registering static IPs, DDNS services (there is support for free No-IP), UPnP, etc.

It is also possible to connect to the Xiaomi router from a smartphone.

Setting up the Internet on the Xiaomi Mi WiFi 3 router

I set up the Internet through a Xiaomi router more than once and I can say that, although rarely, there are errors in determining the connection type - remember I said that it is detected automatically? So, to change it manually, you need to select your type of connection to the provider from the drop-down list in “Settings” in the “Internet” section. Three options available

PPPoE
DHCP (dynamic IP)
Static IP

Setting up Xiaomi Router 3 for BeeLine (L2TP)

Unfortunately, the stock firmware does not support the L2TP and PPTP protocols, which means that it is not possible to connect the router to the Internet from the Beeline provider. Another option is to install an intermediate cable router and connect Xiaomi to it.

If you have a PPPoE connection, then enter your login and password in the fields indicated in the image below.

If the provider has configured mandatory binding by the MAC address of the computer, then below on the page in the same section there is an opportunity to clone it from the main computer. The MAC of the computer will be detected automatically - we just have to click on the left button to use this function.

That's all - after this the Internet will start working. Well, I’ll tell you how to go into the settings of a Xiaomi router with in a separate article.

A feature of Xiaomi Wi-Fi routers that makes it difficult to set up the Internet and Wi-Fi network is problems with interface translation. Even in the English version of the firmware, some inscriptions remain in Chinese. To configure these items via a browser, it is recommended to use an online translator, such as Google Translate.

Differences in setting up Xiaomi routers

All Xiaomi models are configured through the same interface. It can be used:

Administrative panel in the browser;
Client for Android;
iOS application;
Utility for Windows;
Program for Mac.

All stages of specifying parameters are the same, but depending on the availability of additional functions, different settings are available for different devices. The Mi WiFi 3 and Mi WiFi Mini routers support two wireless network bands: 2.4 GHz and 5 GHz. They also have a USB port that allows you to connect external devices (hard drives, flash drives).

The Nano model is similar in design to the Mini router. The differences between the routers are visible on the back panel. Instead of a connector for the Xiaomi power supply, a Micro-USB input is used. This allows you to connect the "Mi WiFi Nano" even through a mobile phone charger. In addition, there is no USB port for connecting external drives.

Note! The Xiaomi lineup also includes professional routers with built-in memory up to 6 TB. They are distinguished by higher technical characteristics and the presence of active cooling.

Connecting and logging into the web interface

Plug the ISP cable into the blue input on the back of the router. If you have home computers or laptops with an Ethernet connector, connect them with a cable to the gray ports. Unlike most routers from other brands, budget Xiaomi devices do not come with a network cable. You need to purchase it separately or use a Wi-Fi connection.

When purchasing with delivery from China (for example, from the Aliexpress store), you should also take into account that the power supply plug is type “A”. To plug into a Russian outlet you will need an additional adapter. Connect the adapter to the router and turn it on to the network. There is no power button on Xiaomi routers; devices start working immediately after connection.

Despite the availability of client applications for smartphones and computers with different OSes, the admin panel remains the universal method of configuration. It can be accessed using any software and hardware platform. Just launch the browser and enter the standard IP of the Xiaomi router into the address bar: 192.168.31.1.

When connecting for the first time, check the box confirming that you agree to the terms of the license agreement and click the button above it. The system will prompt you to enter a new Wi-Fi network name (SSID) and its password. Provide this information and proceed to the next step. Then enter a new password to enter the router settings. When the device reboots, connect to the created network and enter the administrator password.

The start screen contains basic information about the router and statistics on its operation. At the bottom of the page, graphs of network usage (wired and wireless) and the load on hardware components are displayed. If the router operates in two Wi-Fi bands, data is displayed for each connection created.

Important advice! If you encounter difficulties connecting, use the built-in connection diagnostic utility. Rebooting the router may also help.

Internet and Wi-Fi setup

To specify the provider data, click the third item in the top menu: “Common settings”. Open the "Internet settings" tab and select which settings you want to change. Various connection protocols will be available in the drop-down list. If the type of connection you are using and your account details are unknown to you, check them with your Internet provider support.

Wireless network settings on Xiaomi routers are indicated on the adjacent tab in the same menu: “Wi-Fi settings”. Dual-band routers allow you to set separate SSIDs and security settings for 2.4 and 5 GHz networks. In the “Encryption” column, select the encryption protocol, and in the text field below it, enter the Wi-Fi access key.

You can set the guest network at the bottom of the page. To launch it, change the value of the first item from “Shut down” to “Open”. Enter the guest Wi-Fi SSID and select the protection type from the drop-down list. If you specify encrypted access, you will also need to enter the password for the guest network. The settings will take effect after the router is rebooted.

While users are making fun of Xiaomi, jokingly asking the authors when their toilet paper or toilet will be reviewed, the company is seriously releasing these products and, to spite the haters, they are even in some demand (mainly in China, of course). And now Xiaomi is giving a worthy answer to customers who complain about prices, commenting with phrases - “Yes, for that price it should make MiNet.” Please! A special MiNet button is in the most visible place.

But seriously, Xiaomi has released a new WiFi router, which I hastened to order to replace my Xiaomi Mini Wifi Router. Xiaomi Mini has worked successfully for more than 2 years and a replacement was due when I switched to a new tariff plan from my provider. 200 megabits - that’s exactly how much I received for downloading, but I ran into a 100 megabit WAN port. The review will contain a short comparison of speed, coverage range and characteristics.

I didn’t come to Xiaomi routers right away; before that I used the popularly overrated TP-Link, which is literally nothing in the budget segment. Then there was the terribly buggy Asus, which frayed my nerves for half a year with its constant network failures. In the end, I couldn’t stand it anymore and started looking for a replacement. There was only one requirement - stable operation, ease of setup and the presence of a 5 GHz range. I found all this in Xiaomi Mini, I did not take into account only the moment with 100 megabit ports, because then this speed seemed prohibitive. The router itself can distribute at higher speeds when, for example, it is used as a server (from a flash drive or HDD), but the Internet was limited to 100 megabits, and time does not stand still. In terms of stability, I had no complaints about the Mini - setting it up through the application took 5 minutes, and after 2 years of work I even forgot what the settings interface looked like, because I only went there a couple of times, and then just for the sake of curiosity. There was no drop in speed, accumulation of errors and no need for periodic resets, like with TP-Link. Therefore, it was decided that the next router will also definitely be Xiaomi. The choice fell on a new product, let's look at its main technical characteristics:

Video version of the review

When switching from Mini Wifi Router to Mi Router 4, I won in all areas at once. Therefore, if the question is about replacement, the answer is yes, it’s definitely worth changing. Compared to its predecessor Xiaomi Mi Router 3, there are also quite serious changes. Although they concern most of the performance. I offer a small comparison table; for convenience, I have highlighted changes for the better in bold.

Xiaomi Mini Wifi Router	Xiaomi Mi Router 3	Xiaomi Mi Router 4
	Single-core processor MT7620A with a frequency of 580MHz	CPU dual-core MT7621A with frequency 880MHz
RAM 128 MB DDR2	RAM 128 MB DDR2	RAM 128 MB DDR3
Memory 16MB SPI Flash	Memory 128Mb SLC Nand Flash	Memory 128Mb SLC Nand Flash
	WAN network, 2xLAN - up to 100 Mbit/s	WAN network, 2xLAN - up to 1 Gbit/s
	Antennas: 2.4 Ghz WiFi 2x2 (up to 300 Mbit/s); 5 Ghz WiFi 2x2 (up to 867 Mbit/s)	Antennas: 2.4 Ghz WiFi 2x2 (up to 300 Mbit/s); 5 Ghz WiFi 2x2 (up to 867 Mbit/s)

That is, in simple words, Mi Router 4 has become much more powerful and has acquired gigabit ports. Let's take a closer look at the new product. The box is quite massive, on the front there is an image of the model and the name in Chinese.

The main advantages are described on the reverse side, also in Chinese. And of course, special attention was paid to the MiNet button, with which you can connect smart electronics to a home network controlled by Mi Router 4 (including smart home components produced by MIJIA and other Xiaomi sub-brands). Just by pressing one button, without entering a password.

The router is neatly placed in a box and covered with translucent film. Having taken it out, you can find the QR code, clicking on it to download the MiRouter application. This is the easiest and most convenient way to connect and configure the device; in addition, it is possible to configure it via the WEB interface.

The power supply and instructions were placed in a separate niche.

The instructions describe how to connect and configure the router, everything is accompanied by pictures.

The power supply, as in previous models, is 12V\1A, American plug (the store did not forget to include an adapter for a European plug).

The design is similar to the models of the third series, but with larger curves of the body. 4 non-removable antennas can be tilted in depth (forward\back) and to the sides (left\right). The color has not changed - white. The memory is still fresh of how negatively people reacted to the white casings of the routers of the first Xiaomi models, and only over time many realized that it was really practical. Dust is not visible on the white body and the device always looks neat visually.

Its small size and thickness allow it to be placed on almost any table or shelf. Among the definite disadvantages I would include the lack of wall mounting capability; for Xiaomi routers this is just some kind of disease.

Like all xiaomi products, the router looks truly stylish.

Each antenna is engraved with the MiWiFi logo

On the back wall you can find one WAN port and 2 LAN ports. For home purposes, this is enough, for example, 1LAN goes to a wired connection to a computer, another LAN to a wired connection to a TV box. The rest is by air. For example, for me, everything is connected only by air. There is a hidden Reset button, but I never used it in the previous model. Even if you need to reset the router, for example, to clean the RAM, it is much easier to do this by turning off the power. Compared to its predecessor Mi Router 3 or my previous Mini Wifi Router, this model has removed the USB connector.

The physical Mi button is located in the center of the body. For those who have not yet understood, the proprietary MiNet technology turned out to be simply an analogue of the Wi-Fi Protected Setup function, or simply WPS. Let's say you have a smart lamp from MIJIA (a sub-brand of Xiaomi) and you want to connect it. Activate the network search on the lamp, according to the instructions, then press Mi on the router and wait until the connection occurs. There is no need to enter a password. That's the whole point of the MiNet function, otherwise you're already daydreaming :)

Minor changes affected the LED. If in the Mini Wifi Router it shines directly and in the dark turns into a hellish spotlight, then here the glow is directed at a slight downward angle. The brightness of the LED is slightly lower and now in working condition it is not blue, but light turquoise. In total, the LED can shine in 3 colors - turquoise during operation, orange during loading, and red during critical errors.

Turning the router over reveals many ventilation holes. In the center is a sticker that shows the address for connecting to the Web interface, the name of the default network and other information.

A hidden screw was placed under the sticker. By unscrewing it, you can open the case latches and disassemble the router.

As usual, Xiaomi used black textolite. The central processor and memory are covered with metal screens, which simultaneously serve as radiators. On the reverse side, the board is connected to a metal plate through heat-conducting rubber bands; it plays the main role in heat removal. The manufacturer left a small Easter egg on the board, ARE YOU OK!!! - ARE YOU OKAY!!!

The 2.4G and 5G antenna connectors are connected with the corresponding connectors. 2 antennas for each channel.

back side

Toshiba JV6548 chip, presumably this is memory.

Setup and connection

Everything here is elementary. Scan the QR code from the box\instructions or install the MiRouter application from the market yourself. In the application, setting up connections and managing functions is really very simple and takes no more than a couple of minutes. If you have a Mi account, good, if not, you need to create one. I have had the MiRouter application installed for a long time and it automatically detected that a new router had appeared on the network, after which it suggested that I set it up as a new device or transfer the settings from the previous one. I chose to set up a new one, after which the Internet is checked. Next, come up with a network name and password. That's all the setup.

Now let's look at the most interesting features of the application and what you can do with it. The main page displays the activity of connected devices - when it entered the network, how much traffic it used, etc. You can go into each device and limit its speed or block access to the network completely. Next is the settings section - here you can change the password or network name, set speed limits for guest devices, select a region (change the application language), set the time and date, reset the settings to factory settings and update the firmware.

If for some reason the router does not pick up all the network settings automatically, you can enter them manually.

What interesting things can you do through the application? In the WiFi settings, you can configure each network separately (2.4G and 5G), you can adjust the signal strength in each range individually (weak, standard and maximum) or turn off the unused range completely. You can also create black lists of devices that will be denied access to the network, or vice versa - a white list with allowed access. There is a timer to automatically turn on/off at night. When no one needs the Internet, the router will turn off.

There is a whole section with special utilities, for example, in QoS you can manage connection limits, limiting the speed to the desired value for an individual device. By the way, the router supports up to 128 devices simultaneously. We need to give an idea to hotel owners in Turkey, otherwise they always have problems with Internet access in the lobby. Although how many simultaneous connections are there? 20 - 30? Well, 50 maximum :) Also, using additional tools, you can create a guest network, configure a VPN, test Internet speed, etc. Some functions will not work, for example Photo Backup, because there is no USB connector for connecting the drive. Another useful little thing for me was the ability to turn off the indicator light in the system settings.

What I generally like about routers from Xiaomi is the ease of setup and stability of operation. Craftsmen flash them with modified firmware, for example Padavan. Maybe it adds some features, but I don't need it. Everything you need is on stock, and most importantly it works stably.

By the way, if you want to use the Web interface when setting up the router, then this option is also available here. Enter the address indicated on the sticker from the router into the address bar of your browser. Here, however, everything will be in Chinese, but if you use Chrome, then simply right-click anywhere on the screen and select “translate into Russian,” after which you get a Russian-language site. Surprisingly, the translation is very correct and understanding the settings is not difficult. The main page displays interesting statistics on the load on the network, processor and memory of the router. There are also statistics on the amount of traffic consumed by each device. All information is available online.

By analogy with a mobile application, you can manage connections, adjust Internet speed and limit, block devices, create black and white lists.

Setting up network, password, signal strength, encryption type, etc.

General settings menu

Advanced settings

Now let's run some user tests. The most important question is, of course, increasing the speed of the Internet via WiFi, which is what the router was bought for. At the moment, my main smartphone is Oppo F7, which on the previous router had the following indicators: in the 2.4 Ghz range, the download speed was 45 - 50 mbps, in the 5 Ghz range - up to 95 mbps. With the new router, the speed at 2.4 Ghz did not increase much; it was already almost at the maximum possible. But at 5 Ghz I have already reached my tariff plan, having received a maximum of 200 mbps.

Signal quality and coverage range have also changed, especially in the 5Ghz range. Previously, I could only get maximum speed in the room with the router or in the next room, and then the signal level dropped and the speed dropped accordingly. For example, in the kitchen I could already get a maximum of 40 Mbps, which actually equalized the speed with the frequency of 2.4 Ghz. Upon entering the entrance, the smartphone lost the network and switched to 2.4G, and the flight below, where there was a smoking area, the 2.4 Ghz band also periodically dropped out. These are the indicators I took using WiFi Analyzer from the previous Mini Wifi Router:

Room with a router

Back room (2 walls)

In the corridor and entrance, 5 Ghz already periodically fell off and the smartphone switched to 2.4 Ghz. And the flight below was already falling off and 2.4 Ghz. On the street I only received 2.4 Ghz and only strictly under the balcony.

And here are the indicators from the new Mi WiFi 4 router: Room with a router

Back room (2 walls)

At this stage, it is clear that the signal level drops slightly and evenly on both bands. The speed within the apartment is maximum everywhere. But in the entrance it is already falling more strongly, because a load-bearing concrete wall is being added.

Having gone down one flight, the 5 Ghz band is already barely catching. But at 2.4 Ghz there is complete order here.

On the street near the entrance (I live on the 8th floor), as well as within 50 meters from it, only 2.4 Ghz can be received. The second range no longer finishes. All tests were carried out with the “standard” signal strength settings. If you don’t go into details when comparing numbers, even if you walk through different rooms of an apartment with a WiFi signal detector, you can notice the difference with the naked eye.

To summarize, I would like to note that Xiaomi managed to release another high-quality router, which expanded its already wide range of devices. I got everything I wanted from it in full, I’m 100% happy with the update. Like other brand products, this one is aimed primarily at simplicity and ease of use. Do you know which router is considered good? The answer is the one they forgot where it stands. And this is true - after connecting and setting up the device, all you have to do is remember to periodically wipe it from dust. Everything else can be done directly from your smartphone.